Waterborne floor paint for interiors and exteriors
PAVIFLEX ECO is a modern, waterborne, low odor, rapid drying satin paint for floors, ideal for both interiors and exteriors. It an easy to use one-pack product formulated with top quality special modified acrylic resins that give the product outstanding characteristics of durability, hard wearing, high adhesion even to difficult surfaces such as ceramics and can it also resist to light tire traffic. The product is also recommended for use on walls when exceptional resistances are required.
Interior or exterior painting of floors in basements, stairs, residential garages, porches and terraces.
Surfaces to treat must be perfectly dry, clean, sound, even and free from any foreign substances or loose friable material. Degrease and brush well. For previously painted surfaces, remove any traces of weak paint, sand and clean well.
Colors supplied: Grey RAL 7038, Red RAL 3009
By brush or roller.
Cement: apply the first coat thinned with 5% water and 2nd coat undiluted.
Ceramics: glossy surfaces should be dulled by sanding, clean and apply 2 coats undiluted.
Wood: 2 coats undiluted.
Ready to use or if necessary with max. 5% water.
(per coat): up to about 8-9 m²/ℓ
Waterborne, 2-pack, mid-sheen epoxy enamel paint
Waterborne, two-pack, mid-sheen epoxy enamel paint providing a tough, extremely hard wearing and highly resistant surface. Meant for coating interior floors of warehouses, workshops, garages, schools, etc. even on concrete water tanks. Ideal for internal use in areas subject to foot and rubber-tyred vehicle traffic with excellent resistance.
New concrete substrate: Ensure no silicones or waxes are contained and that the concrete has aged for at least 28 days. Remove any decayed or incoherent parts and vacuum away dust well. Do not apply with a substrate humidity above 15%. Wash the substrate with a 10% solution of muriatic acid allowing it to react on the surface till all the bubbling has stopped. Rinse well with water and allow to dry. On old concrete surfaces: clean away any existing trace of oils or grease with specific products and treat as described above for new surfaces. Any crack filling or void repair work should be effected with appropriate epoxy mortars.
Mix together packs A and B in the given ratio, thin and stir thoroughly. Apply the prepared mixture with a brush or short-pile roller. Two coats normally confer good resistance but in case of severe conditions and extra resistance is required, a third coat is recommended.
With 33% water.
(per coat): 10-12 m²/ℓ
Waterborne rust converter
Converfix is a rust converter based on waterborne polymeric resins that chemically reacts with rust converting it to a shiny and stable, black colored organometallic substance. The product ensures an excellent anchorage to the metal surface and is high in antioxidant capacity in the medium term.
For use on rusted surfaces. It is also effective on new metallic surface.
Unpainted metal surfaces: wire brush the surface to remove any loose rust and clean off the dust with a water dampened rag.
Painted metal surfaces: scrape off all unfixed paint, wire brush to remove any loose rust and clean off the dust with a water dampened rag.
Apply by brush, roller or by spray. Use a quantity of product sufficient to wet the corroded surface and avoid excess recoating. The application can also be made onto humid substrates. The treated surfaces should be coated over with a good finishing paint after 36 to 48 hours to ensure that the polymeric reaction has been totally completed.
Ready to use.
(per coat): 12-15 m²/ℓ
Extra-strong paint-stripper for enamels, varnishes and paints
A universal, solvent borne paint remover with neutral PH, highly effective on all types of waterborne, solvent or oil-based paints and coatings even with many layers. It can also be used for finishes based on nitrocellulose, acrylates, polyesters, polyurethanes, air or oven curing enamels, stuccos, carpet and parquet glues or marine paints.
Apply a thick coat (2-3 mm) of Paint Stripper by brush or trowel and spread it evenly over the surface. Allow sufficient time for the stripper to dissolve the layer, until it starts to wrinkle up and lift itself off the substrate. At this point you can scrape off the dissolved layer with a scraper. The actual dissolving time will depend on the thickness, the type and age of the paint and can vary from various minutes for emulsion paints to 2 hours or more for catalyzed or polymerized coatings. For tougher coatings and in hot weather, it is advisable to apply a film of polythene over the applied stripper. Do not use the product on plastic surfaces nor on surfaces that are heated or exposed to the sun.
Ready to use.
(per coat): about 0,5 m²/ℓ
Universal insulating primer for interior and exterior
Waterborne, concentrated, sealing primer that forms an alkaliresistant, insulating film, improving the adhesion and the resistance of the finishing coat.
Surface preparation of new walls in concrete, masonry, cement, lime or gypsum plasters or where old paints are not sufficiently sound.
Surface to treat must be clean, dry and even. Where necessary effect repairs on cracks or voids and if needed level the surface.
By brush or roller.
Add 5 or 6 parts of water to 1 part of ADIFIX.
(per coat): about 40 – 50 m²/ℓ
White, waterborne, sealing primer
Monofix is the ideal prepainting product that primes, seals, uniforms absorption and gives an initial hide to the wall, ensuring an excellent base to the subsequent topcoats. It is alkaline resistant and significantly improves the application, the resistance and durability of the finish coat, enabling to save on the number of topcoats required.
Sealing primer for wall surface preparation on concrete, rendered masonry, gypsum, etc.
Surfaces to treat must be clean, dry and even. If necessary effect repairs on cracks or voids and if needed, level the surface.
Apply a coat of Monofix by brush or by roller.
Ready to use or with max. 5% to 10% water.
(per coat): 10 to 12 m²/ℓ
Paint edging roller
Painting a feature wall in a different color requires ability, precision and laborious preparation. Could it be possible to do it quickly, avoiding masking, ladders and any peeling of the previous coat of paint? Yes, if you use LAMPOPIU’. This tool will allow you to quickly and easily get a sharp cut edge at corners, around doors or windows and create borders from zero to 4 cm width.
Universal colorants in handy squeeze bottles for coloring or for adjusting tones of paints and coating products.
Chiudendo questo banner acconsenti all’uso dei cookie.OkLeggi di più